How to Install an Anti-Scald Shower Valve

Posted by in Home Improvement Tips, on March 5, 2016

Watch the full episode: https://www.youtube.com/watch?v=d2hpPmgsS_o

Richard Trethewey replaces a three-handle shower valve with a single-handle anti-scald valve. (See below for a shopping list, tools, and steps.)

Click here to SUBSCRIBE to the official This Old House YouTube channel: http://www.youtube.com/subscription_center?add_user=thisoldhouse

Shopping List for How to Install an Anti-Scald Shower Valve:
– Single-lever pressure-balance shower valve with cover plate
– Emery cloth, for buffing clean copper pipe ends
– Lead-free solder and flux, used for soldering
– Plumber's putty, for creating a watertight seal around the valve's cover plate
– Cotton cloth, used to buff the valve clean

Tools for How to Install an Anti-Scald Shower Valve:
– Pliers
– Screwdriver
– Cordless drill
– Handle puller, used to remove stubborn valve handles
– Pipe wrench, used to unscrew stem units from the valve
– 1/8-inch-diameter masonry bit, for boring holes through tile
– Oscillating multi-tool and carbide-grit blade, used to cut tile
– Hammer and 1/2-inch cold chisel, for chipping tile off the wall
– Wet/dry vacuum, used to collect dust
– Reciprocating saw with metal-cutting blade, for cutting out the old valve
– Tubing cutter, used to cut copper pipe
– Plant mister, used to mist the wall cavity with water prior to soldering
– Propane torch, for soldering
– Digital thermometer, used to check hot-water temperature

Steps for How to Install an Anti-Scald Shower Valve:
1. Turn off the water to the shower, then unscrew the three handles and escutcheon plates from the existing shower valve
2. If the handles are rusted in place, free them with a handle puller.
3. Use a pipe wrench to loosen and remove the stem units from the hot-water valve, cold-water valve and diverter.
4. Hold the cover-plate template centered over the existing valve, then trace the template's outline onto the tiled shower wall.
5. Use a drill and 1/8-inch-diameter carbide-tipped masonry bit to bore six evenly spaced holes through the tile around the template's outline.
6. Cut the tile along the marked outline using an oscillating multi-tool fitted with a carbide-grit blade. Collect the dust with a wet/dry vacuum during cutting.
7. Chip the tile off the wall with a hammer and 1/2-inch cold chisel.
8. Cut out the old valve using a reciprocating saw with a metal-cutting blade.
9. Dry-assemble the copper pipe and fittings to join the new pressure-balance valve to the existing hot- and cold-water supply pipes.
10. Unscrew and remove the spindle from inside the new valve.[BR]
11. Disassemble the parts, apply flux to the copper pipe, fittings and valve, then reassemble the parts.
12. Next, spray water into the wall cavity with a plant mister to reduce the risk of starting a fire.
13. Solder the new valve to the water-supply pipes.
14. Reinstall the valve spindle that was removed in Step 10, then turn the water back on.
15. Test the valve by sliding on the handle and turning on both the hot and cold water. Remove the handle.
16. Roll a ball of plumber's putty between your hands to form a long 1/2-inch-diameter rope. Press the putty against the upper, rear section of the valve's cover plate.
17. Screw the cover plate to the shower wall centered over the valve. Scrape away any excess putty that squeezes out from behind the cover plate.
18. Set the escutcheon plate over the cover plate, then screw it partway onto the valve body.
19. Slip a rubber gasket behind the rear, upper section of the escutcheon plate. Finish tightening the screws.
20. Turn on the hot water, then use a thermometer to check the water temperature.
21. Use a screwdriver to adjust the temperature limit on the valve to ensure the hot water doesn't get any hotter than 120-degrees F.
22. Slip the cap assembly and handle onto the valve, then secure both with a single screw.
23. Cover the screw head with a push-on index button.
24. Buff the valve clean with a soft cotton cloth.

Follow This Old House and Ask This Old House:
Facebook: https://www.facebook.com/ThisOldHouse
Twitter: https://twitter.com/thisoldhouse
https://twitter.com/asktoh
Pinterest: http://www.pinterest.com/thisoldhouse/
G+: https://plus.google.com/+thisoldhouse/posts
Instagram: http://instagram.com/thisoldhouse
Tumblr: http://thisoldhouse.tumblr.com/
For more stories like this from Bay Area Plumbing Headquarters, bookmark our site.

Leave a Reply

Your email address will not be published. Required fields are marked *